banner



How To Change Mitsubishi Lancer 2008 Headlight Bulb

Mitsubishi Lancer Headlight Bulbs Replacement Guide
How to modify a low axle, loftier axle, forepart turn indicate or side marker bulb in an 8th generation 2008-2015 Lancer.

Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-001
2015 Lancer Headlight
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-002
Depression Beam Lite
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-003
Base of Low Beam Bulb
This automotive maintenance tutorial was specifically written to assist owners of the eighth generation (2008, 2009, 2010, 2011, 2012, 2013, 2014 & 2015) Mitsubishi Lancer in checking or changing the engine spark plugs in the MIVEC 4B11 2.0 liter or the MIVEC 4B12 ii.4L inline 4 cylinder motors.

Owners of other Mitsubishi vehicles such every bit the Mirage, Lancer Evolution ("Evo"), Outlander, 3000GT, Diamante, Eclipse, Effort, Galant, Montero, ASX, Triton L200 and Raider may also find these DIY instructions to be helpful.

The replacement bulb part numbers are as follows: Depression Beam # 9006, High Beam # 9005, Forepart Turn Point 7440A (also WY21W or 7440NA) and Side Marking # 2827 (or WY5W).

On near Lancer models, no tools are needed to change the low beam bulbs.

You may need a 10mm socket with a ane/4" drive ratchet and a flathead screwdriver to access the high beam and turn signal bulbs.



Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-004
Release Power Plug
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-005
i/four Turn Counterclockwise
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-006
Pull Out Sometime Bulb
The first two steps are to open the hood and then move to the side of the vehicle with the burnt out headlight seedling.

The Low Axle bulb is located well-nigh the center of the assembly closer to the outer edge.

(To access the driver side low axle bulb on Lancer models with the turbocharged engine, yous volition need to remove the 10mm bolt that secures the relay box in place. For the passenger side on a turbo model, just lift upwards the engine coolant reservoir.)

Achieve in behind the housing and gently pull dorsum the retaining clip on the depression beam bulb'south electrical connector.

Slide the plug straight off the base of the bulb.

Rotate the quondam bulb one/iv turn counterclockwise and pull it straight out of the housing.

Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-007
Sylvania 9006 Low Axle
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-008
Insert New # 9006 Bulb
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-009
1/4 Turn Clockwise - Lock
Effort to avoid touching the glass role of the new halogen bulb with your fingers or anything greasy in the engine bay.

If y'all practice get the new bulb dirty, wipe it clean with a newspaper towel moistened with rubbing alcohol.

Insert the new # 9006 low beam bulb in to the housing and rotate it 1/4 turn clockwise to secure it in place.

Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-010
Push On Power Plug
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-011
Loftier Beam - Center of Housing
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-012
Loosen 10mm Bolt
Button the power plug straight on to the base of the new bulb until it clicks securely in to identify.

The High Beam bulb is located at the center of the headlight housing.

To access the high axle bulb on the passenger side of the vehicle, you'll need to remove the 10mm bolt that holds the windshield wiper fluid filler hose in place.

Loosen the 10mm bolt in the counterclockwise direction and then push back the wiper fluid hose. Set the 10mm bolt aside in a safety place.

Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-013
Push Back Wiper Fluid Hose
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-014
High Beam Grit Comprehend
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-015
1/4 Turn Counterclockwise
Rotate the round black plastic grit cover on the loftier beam bulb housing i/4 turn counterclockwise before pulling it direct off. Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-016
Base of Loftier Axle Bulb
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-017
1/4 Turn Counterclockwise
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-018
Sylvania # 9005
Gently pull back the retaining prune on the electrical connector and slide the plug straight off the base of operations of the quondam seedling.

Rotate the base of the old high beam bulb 1/four turn counterclockwise before pulling information technology direct out of the housing.

Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-019
Install New Loftier Beam
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-020
Cover - 1/four Turn Clockwise
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-021
Plow Signal - Inner Corner
Avoid touching the drinking glass role of the new halogen bulb with your fingers or anything greasy in the engine bay.

Insert the new 9005 bulb in to the housing and rotate it one/4 turn clockwise to lock it in place.

Replace the blackness plastic dust cap and rotate information technology 1/4 plow clockwise to secure it in place.

The Front Turn Point seedling is located at the inner border of the headlight housing.

Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-022
Turn Signal Bulb Socket
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-023
Plastic Radiator Embrace
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-024
Pry Up Center of Popular Rivet
To access the front turn signal bulb sockets, yous'll need to remove the fasteners on the blackness plastic radiator cover.

Pry up the center function of each pop rivet with a flathead screwdriver then remove the entire fastener.

Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-025
Remove Plastic Fastener
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-026
Remove Other Popular Rivets
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-027 Remove all of the pop rivets on the radiator cover.

To detach the air intake duct, y'all'll need to remove the two plastic Phillips head screws.

Yous don't take to detach the air intake duct if you are simply replacing the passenger side forepart turn signal lite bulb.

Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-028 Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-029
Lift Up Radiator Shield
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-030
Driver Side - Relay Box Bolt
Either remove the entire radiator cover or but enhance the passenger side of the shield to access the turn point bulb socket. Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-031
one/4 Plough Counterclockwise
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-032
Remove Seedling Socket
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-033
Pull Out Onetime Bulb
Attain in behind the headlight housing and rotate the yellow plough point bulb socket ane/4 turn counterclockwise before pulling it straight out. Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-034
Two Air Intake Screws
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-035
Stripped Plastic Spiral
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-036
Push In New # 7440A
I took pictures of the two plastic Phillips head screws on the air intake duct that I wasn't able to remove since they stripped immediately.

I would recommend that y'all pry out these screws and supersede them with pop rivet fasteners that are easier to remove in the future.

Pull the onetime turn point bulb straight out of the socket and button in a new # 7440A bulb. You lot may also exist able to utilize the # 7440NA or WY21W bulb.

Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-037
1/4 Plough Clockwise - Lock
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-038
Supplant Plastic Cover
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-039
Button In Pop Rivets
Re-insert the bulb socket in to the housing and rotate information technology 1/4 turn clockwise to secure it in place.

Lower the plastic radiator embrace back in to place.

Re-insert the plastic popular rivets and push button down the heart part of fastener to secure them in identify.

Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-040
Replace Fasteners
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-041
Side Marker - Outer Border
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-042
1/four Turn Counterclockwise
The Front Side Marker bulb is located at the outer edge of the housing.

Accomplish in and rotate the seedling socket 1/4 turn counterclockwise before pulling it directly out of the housing.

Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-043
Seedling Socket Removed
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-044
Pull Out Old Bulb
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-045
Push button In New # 2827
Pull the old bulb directly out of the socket and push in a new amber colored # 2827 or WY5W seedling. Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-046
1/4 Turn Clockwise - Lock
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-047
Replace Wiper Fluid Hose
Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide-048
Test New Headlight Bulbs
Re-insert the side marker bulb socket in to the housing and rotate it 1/four plow clockwise to secure it in identify.

If you removed the windshield wiper fluid fill up tube, replace the 10mm commodities by turning it clockwise until it is snug.

Test the new bulbs by turning on the headlights, activating the hazard signals and flashing the loftier beams.

For more, cheque out my other 2008-2015 Mitsubishi Lancer DIY Repair & Maintenance Guides.

Source: https://www.paulstravelpictures.com/Mitsubishi-Lancer-Headlight-Bulbs-Replacement-Guide/

Posted by: liskalogre1972.blogspot.com

0 Response to "How To Change Mitsubishi Lancer 2008 Headlight Bulb"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel